Author |
Message |
Brian Vogel
Grand Master Username: guyslp
Post Number: 2557 Registered: 6-2009
| Posted on Sunday, 06 May, 2018 - 06:55: | |
A few months back I had asked about how to get the markings on the crankshaft damper readable again for the purposes of timing. Jim Walters recommended using Lacquer-Stik for this purpose and I must say the result is great. Here are "after" photos, from topside (where it matters most) and underside after the application of the Lacquer-Stik and promptly wiping off the excess: One could use this for many other purposes, and it comes in multiple colors as well: I can imagine filling in lettering on any number of things where the original color has worn away. Brian |
Omar M. Shams
Grand Master Username: omar
Post Number: 1502 Registered: 4-2009
| Posted on Monday, 07 May, 2018 - 05:06: | |
just bought a stick. |
Jim Walters
Prolific User Username: jim_walters
Post Number: 152 Registered: 1-2014
| Posted on Tuesday, 08 May, 2018 - 03:01: | |
If you are filling lettering like on the ignition switchbox give it a very light wipe after applying then let it dry a day or two before polishing the background to remove the residue. SRH8505 SRC18015 SRE22493 NAC-05370 www.bristolmotors.com |
Brian Vogel
Grand Master Username: guyslp
Post Number: 2561 Registered: 6-2009
| Posted on Tuesday, 08 May, 2018 - 04:24: | |
Jim, Thanks for that tip, too. When looking at reviews someone mentioned that it takes a couple of days to dry completely. After my little experiment with that Lucas relay (which I know never had anything as far as fill-in on the lettering) it hit me that there was something else this would be great for: The older I get the more frustrated I become when trying to read the markings on socket sets and, even worse, drill bits. Although yellow or red might be slightly better on chrome, white works quite well and is even more visible than the photo presents. For years I've been marking my metric versus SAE sockets with nail enamel so that I don't grab one when I mean to grab the other, and the filled in size designations are an important added bonus. Brian |
Mark Luft
Prolific User Username: bentleyman1993
Post Number: 186 Registered: 10-2016
| Posted on Tuesday, 08 May, 2018 - 05:32: | |
Great idea Brian! When I was a young lad working at a rental center in MD we had a small engine mechanic that had all of his tools (wrenches and sockets) painted different colors. I asked him what was up with that and he replied, "I can find any size wrench I need from across the room. If I need a 1/2 inch wrench I can tell you to get me the red wrench, or if I need a 9/16 socket you can bring me the blue one". This saved Harry a lot of time checking sizes. Thus allowing more time for Harry to drink Pabst Blue Ribbon beer and tomato juice. The things we remember.... |
Patrick Lockyer.
Grand Master Username: pat_lockyer
Post Number: 1857 Registered: 9-2004
| Posted on Tuesday, 08 May, 2018 - 06:27: | |
Brian throw those sockets out and get the six sided type unless you like rounding nuts and bolt heads. |
Maxwell Heazlewood
Prolific User Username: tasbent
Post Number: 182 Registered: 9-2017
| Posted on Tuesday, 08 May, 2018 - 10:27: | |
The use of a hair dryer or heat gun with continuous passing strokes will dry it out much quicker |
Brian Vogel
Grand Master Username: guyslp
Post Number: 2563 Registered: 6-2009
| Posted on Tuesday, 08 May, 2018 - 11:04: | |
Mark, You can still buy sockets in anodized colors at Harbor Freight, e.g, these deep sockets in metric sizes and SAE sizes (and they have regular ones, too). I actually have the deep sockets in both. My problem is that there is overlap in the colors used and, since I'm not using these things on a daily basis, I don't ever remember what color goes with what size. Perhaps beer and tomato juice would help me with remembering. Then again, perhaps not. [And there were plenty of drinkers of this mix in my hometown of Johnstown, PA, and the surrounding area. That and boilermakers.] Brian |