Author |
Message |
![Top of page](http://au.rrforums.net/forum/icons/mark_top.gif) ![Previous message](http://au.rrforums.net/forum/icons/mark_up.gif) ![Next message](http://au.rrforums.net/forum/icons/mark_down.gif) ![Link to this message](http://au.rrforums.net/forum/icons/tree_m.gif)
michael vass
Frequent User Username: mikebentleyturbo2
Post Number: 577 Registered: 07-2015
| Posted on Thursday, 29 August, 2019 - 04:43: | ![Edit Post](http://au.rrforums.net/forum/icons/tree_s.gif) ![Delete Post](http://au.rrforums.net/forum/icons/delmsg.gif) ![View Post/Check IP](http://au.rrforums.net/forum/icons/checkip.gif) |
Hi All Thanks from the info on here from Stefan Morely and Richard Treacy and all the other contributors ! I have modded my turbo boost system similar to how they advised. see pic
The driver I have used is this ebay item 392094365178 With a 200 ohm load resistor. Now get the proper 6.2 psi boost reliably. Next mod is the boost fooler pot!! Thanks for all the contributors on previous posts on this subject! Cheers Mike |
![Top of page](http://au.rrforums.net/forum/icons/mark_top.gif) ![Previous message](http://au.rrforums.net/forum/icons/mark_up.gif) ![Next message](http://au.rrforums.net/forum/icons/mark_down.gif) ![Link to this message](http://au.rrforums.net/forum/icons/tree_m.gif)
Mark Luft
Frequent User Username: bentleyman1993
Post Number: 289 Registered: 10-2016
| Posted on Thursday, 29 August, 2019 - 04:46: | ![Edit Post](http://au.rrforums.net/forum/icons/tree_s.gif) ![Delete Post](http://au.rrforums.net/forum/icons/delmsg.gif) ![View Post/Check IP](http://au.rrforums.net/forum/icons/checkip.gif) |
Great news Mike! I too wish to mod my turbo. How does it work? Do you FEEL a difference? |
![Top of page](http://au.rrforums.net/forum/icons/mark_top.gif) ![Previous message](http://au.rrforums.net/forum/icons/mark_up.gif) ![Next message](http://au.rrforums.net/forum/icons/mark_down.gif) ![Link to this message](http://au.rrforums.net/forum/icons/tree_m.gif)
Mark Luft
Frequent User Username: bentleyman1993
Post Number: 290 Registered: 10-2016
| Posted on Thursday, 29 August, 2019 - 04:49: | ![Edit Post](http://au.rrforums.net/forum/icons/tree_s.gif) ![Delete Post](http://au.rrforums.net/forum/icons/delmsg.gif) ![View Post/Check IP](http://au.rrforums.net/forum/icons/checkip.gif) |
I can't find the listing. Could you post a link? |
![Top of page](http://au.rrforums.net/forum/icons/mark_top.gif) ![Previous message](http://au.rrforums.net/forum/icons/mark_up.gif) ![Next message](http://au.rrforums.net/forum/icons/mark_down.gif) ![Link to this message](http://au.rrforums.net/forum/icons/tree_m.gif)
michael vass
Frequent User Username: mikebentleyturbo2
Post Number: 579 Registered: 07-2015
| Posted on Thursday, 29 August, 2019 - 05:48: | ![Edit Post](http://au.rrforums.net/forum/icons/tree_s.gif) ![Delete Post](http://au.rrforums.net/forum/icons/delmsg.gif) ![View Post/Check IP](http://au.rrforums.net/forum/icons/checkip.gif) |
Hi Mark Just moving the solenoid from on top of a hot engine and cleaning out makes the thing more reliable, the driver was to give the boost ecu an easier life than driving inductive loads ok here is a link https://www.ebay.co.uk/itm/12V-Input-Optocoupler-Isolation-Module-Solenoid-Valve-Relay-5-12-24V-Output-/392094365178 Here is a basic diagram of how I used it ok I have't have much chance to drive it yet but will be going to Blenheim for the Bentley day so will see then! Cheers Mike![](http://au.rrforums.net/forum/messages/17002/37523.jpg) |