Author |
Message |
Christian S. Hansen
Grand Master Username: enquiring_mind
Post Number: 888 Registered: 4-2015
| Posted on Saturday, 15 September, 2018 - 20:01: | |
Took the '86 Spur in for A/C service today and was floored by the cost of the pressure hoses...$400 made up, $1150 factory. I had assumed that they would be standard hydraulic style hoses, but the story was that they have very special ends that require special machining or fabrication or something that went over my head. Is that true? Not easily made up by a hydraulic hose supplier? The two circuit boards in the climate control box were equally shocking to be rebuilt...$300+ each. The list of other issues went on and on. $$$!! Looks like repairs on other cars are going to take priority as long as I can keep rolling the windows down for "climate control"! . |
Omar M. Shams
Grand Master Username: omar
Post Number: 1668 Registered: 4-2009
| Posted on Sunday, 16 September, 2018 - 00:55: | |
Dear Christian, A hose is a hose is a hose is a hose. If the pressure rating and the compound on the pressure side suits that material then a hose is a hose is a hose. The fittings are all standard A/C fittings like any other car. I pay $35 for my A/C hoses normally. The circuit board is a Rolls-Royce special and they do fail sometimes. |
Kelly Opfar
Prolific User Username: kelly_opfar
Post Number: 209 Registered: 7-2004
| Posted on Sunday, 16 September, 2018 - 13:08: | |
Christian, send me pics of your hose ends. I know a guy who does some machining. Kelly |
Christian S. Hansen
Grand Master Username: enquiring_mind
Post Number: 889 Registered: 4-2015
| Posted on Sunday, 16 September, 2018 - 16:02: | |
The 1986 Silver Spur is serial #13909. Looked at it closer today and yes, the ends are crazy complicated with multiple bends and some sort of can built into it (will post photos tomorrow), but the real issue is: What level of pressure is running on the high side? Can't be that much or it would blow out the evaporator unit? Less than 1000 psi? . |
michael vass
Grand Master Username: mikebentleyturbo2
Post Number: 499 Registered: 7-2015
| Posted on Sunday, 16 September, 2018 - 17:41: | |
Hi Christian , the gauge only goes up to 500 psi pk Mike |
Christian S. Hansen
Grand Master Username: enquiring_mind
Post Number: 890 Registered: 4-2015
| Posted on Sunday, 16 September, 2018 - 17:59: | |
Michael.... Thanks for that. It is as I suspected...relatively low even at the high side. The photos I will post tomorrow will more adequately show a possible "workaround" of simply cutting out the crimped on flexible hose section of the assembly and using appropriate compression fillings to reattach another crimped on section into the assembly rather than recreating the entire hose with its quite complicated metal ends. I have made such a repair on a solid metal hydraulic line on another piece of equipment (bobcat skid steer) where it was impractical to replace a solid metal line without completely disassembling the machine to replace the hard line. I simply cut out the damaged section of the hard line and replaced with a flex line. Worked fine in that much higher PSI application. Wonder if the same "workaround" would also work here? . |
michael vass
Grand Master Username: mikebentleyturbo2
Post Number: 500 Registered: 7-2015
| Posted on Sunday, 16 September, 2018 - 18:55: | |
Hi Christian I would just replace the crimped on flexible too, if I had the tools and hoses. Just make sure the correct hose is used for permeability of the gas and suitable for the oils ,is it r134a you will be using? Good luck Mike |
Christian S. Hansen
Grand Master Username: enquiring_mind
Post Number: 895 Registered: 4-2015
| Posted on Monday, 17 September, 2018 - 17:51: | |
Here is the hose in question. Dye test shows leaking at both crimped ends. While the flexible portion is just a hose, the ends are decidedly proprietary. Cutting the hard line ahead of the front crimp and retaining the portion that goes to the condenser in front of the radiator seems doable but there is no room between the rear crimp and the can so that side will take a bit of reworking. A likely place to cut would be on the compressor side of the can? What is the can? A dryer? Seems odd that it would be built into the hose such that it is not replaceable without also doing the expensive line. Is all this effort worth the trouble given that the old line lasted 30+ years and once done I will not be around in another 30 years when next required. Better to simply sacrifice the back account and replace as designed? The compressor end not only has the can built in, numerous angle bends, but a 180 degree curve that terminates in a fitting at rear of the compressor. Yes, VERY proprietary!! No room between can and crimped end of hose for cutting and inserting a compression fitting to facilitate easy future removal and replacement of the flexible portion of the line. . |
Kelly Opfar
Prolific User Username: kelly_opfar
Post Number: 210 Registered: 7-2004
| Posted on Tuesday, 18 September, 2018 - 01:57: | |
I'm not an A/C expert so I don't know what the can is - probably a drier - but we could eliminate it or replace it or weld extensions on it for an adapter. I weld heat sensitive items like this submerged in water with just the nipple exposed. We could retain the original fittings and make new crimping collars if new ones are not common. I don't see any reason why we can't save this hose and a few hundred bucks. Kelly http://BritishToolWorks.com |