Author |
Message |
![Top of page](http://au.rrforums.net/forum/icons/mark_top.gif) ![Previous message](http://au.rrforums.net/forum/icons/mark_up.gif) ![Next message](http://au.rrforums.net/forum/icons/mark_down.gif) ![Link to this message](http://au.rrforums.net/forum/icons/tree_m.gif)
Richard Greene
Frequent User Username: benzjag
Post Number: 66 Registered: 12-2012
| Posted on Wednesday, 15 November, 2017 - 15:18: | ![Edit Post](http://au.rrforums.net/forum/icons/tree_s.gif) ![Delete Post](http://au.rrforums.net/forum/icons/delmsg.gif) ![View Post/Check IP](http://au.rrforums.net/forum/icons/checkip.gif) |
Does anyone know if there is a substitute fuel sender for the Cloud or an aftermarket one? My sources want $250.00! I feel sure the sender is very similiar to other British cars of the same era! Richard |
![Top of page](http://au.rrforums.net/forum/icons/mark_top.gif) ![Previous message](http://au.rrforums.net/forum/icons/mark_up.gif) ![Next message](http://au.rrforums.net/forum/icons/mark_down.gif) ![Link to this message](http://au.rrforums.net/forum/icons/tree_m.gif)
Jim Walters
Prolific User Username: jim_walters
Post Number: 132 Registered: 1-2014
| Posted on Wednesday, 15 November, 2017 - 15:54: | ![Edit Post](http://au.rrforums.net/forum/icons/tree_s.gif) ![Delete Post](http://au.rrforums.net/forum/icons/delmsg.gif) ![View Post/Check IP](http://au.rrforums.net/forum/icons/checkip.gif) |
You can use a Smiths fuel sender that has terminals for both the gauge and low fuel light, like this one for a Jaguar XK120: https://mossmotors.com/sending-unit-fuel-gauge The only caveat is you will have to shorten and bend the arm to match the Cloud one. SRH8505 SRC18015 SRE22493 NAC-05370 www.bristolmotors.com |
![Top of page](http://au.rrforums.net/forum/icons/mark_top.gif) ![Previous message](http://au.rrforums.net/forum/icons/mark_up.gif) ![Next message](http://au.rrforums.net/forum/icons/mark_down.gif) ![Link to this message](http://au.rrforums.net/forum/icons/tree_m.gif)
Richard Greene
Frequent User Username: benzjag
Post Number: 67 Registered: 12-2012
| Posted on Thursday, 16 November, 2017 - 00:20: | ![Edit Post](http://au.rrforums.net/forum/icons/tree_s.gif) ![Delete Post](http://au.rrforums.net/forum/icons/delmsg.gif) ![View Post/Check IP](http://au.rrforums.net/forum/icons/checkip.gif) |
Understand the bending, but how would you shorten the rod? |
![Top of page](http://au.rrforums.net/forum/icons/mark_top.gif) ![Previous message](http://au.rrforums.net/forum/icons/mark_up.gif) ![Next message](http://au.rrforums.net/forum/icons/mark_down.gif) ![Link to this message](http://au.rrforums.net/forum/icons/tree_m.gif)
Jim Walters
Prolific User Username: jim_walters
Post Number: 133 Registered: 1-2014
| Posted on Thursday, 16 November, 2017 - 04:25: | ![Edit Post](http://au.rrforums.net/forum/icons/tree_s.gif) ![Delete Post](http://au.rrforums.net/forum/icons/delmsg.gif) ![View Post/Check IP](http://au.rrforums.net/forum/icons/checkip.gif) |
I just cut them off with side cutters and re-bend the end loop to hold the float so the overall length is the same. Or, I guess you could cut the new arm in the middle, shorten it the required amount so the two halves equal the length of the old one and solder the arm halves together. SRH8505 SRC18015 SRE22493 NAC-05370 www.bristolmotors.com |
![Top of page](http://au.rrforums.net/forum/icons/mark_top.gif) ![Previous message](http://au.rrforums.net/forum/icons/mark_up.gif) ![Next message](http://au.rrforums.net/forum/icons/mark_down.gif) ![Link to this message](http://au.rrforums.net/forum/icons/tree_m.gif)
Richard Greene
Frequent User Username: benzjag
Post Number: 68 Registered: 12-2012
| Posted on Thursday, 16 November, 2017 - 12:40: | ![Edit Post](http://au.rrforums.net/forum/icons/tree_s.gif) ![Delete Post](http://au.rrforums.net/forum/icons/delmsg.gif) ![View Post/Check IP](http://au.rrforums.net/forum/icons/checkip.gif) |
Great idea! Thanks! Richard |