Blower motor silver cloud 3 Log Out | Topics | Search
Moderators | Register | Edit Profile

Australian RR Forums » Silver Cloud & Bentley S » Blower motor silver cloud 3 « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Francois Charlier
Frequent User
Username: vonplum

Post Number: 51
Registered: 3-2011
Posted on Sunday, 15 April, 2012 - 06:16 pm:   Edit PostDelete PostView Post/Check IP

j have disassembled a blower motor engine of the Rools Royce Silver Cloud 3.
It was blocked.
My problem is: I don't know how to refit this bolwer.
Some parts have fallen like spring.
Do you have a diagram or picture how to replace all the parts?
thank you for your further help
françois charlier
Top of pagePrevious messageNext messageBottom of page Link to this message

Francois Charlier
Frequent User
Username: vonplum

Post Number: 56
Registered: 3-2011
Posted on Monday, 16 April, 2012 - 12:43 am:   Edit PostDelete PostView Post/Check IP

the blower motor:
Top of pagePrevious messageNext messageBottom of page Link to this message

Laurie Fox
Frequent User
Username: laurie_fox

Post Number: 94
Registered: 6-2004
Posted on Monday, 16 April, 2012 - 01:38 am:   Edit PostDelete PostView Post/Check IP

I would feel inclined to let an auto electrician look at the parts first, particularly if the shaft is vertical when the motor is installed. The Smiths motor on the MK VI heater (under the passenger seat) looks similar. There the replacement of worn brushes is difficult even if you can get them, there is no proper thrust bearing and if something stops the armature going round the motor overheats and damages the internal insulation.

Laurie
Top of pagePrevious messageNext messageBottom of page Link to this message

Francois Charlier
Frequent User
Username: vonplum

Post Number: 57
Registered: 3-2011
Posted on Monday, 16 April, 2012 - 03:59 am:   Edit PostDelete PostView Post/Check IP

I fix the noise problem ,
the shaft had seized on the brass ring I already refit the blower motor but I have a doubt with the 2 springs,
when I opened all parts fell.
Top of pagePrevious messageNext messageBottom of page Link to this message

Hubert Kelly
New User
Username: h_kelly

Post Number: 2
Registered: 3-2012
Posted on Monday, 16 April, 2012 - 06:12 am:   Edit PostDelete PostView Post/Check IP

Hi Francois, is there any chance the two springs may have held the brushes against the armature?
Top of pagePrevious messageNext messageBottom of page Link to this message

Francois Charlier
Frequent User
Username: vonplum

Post Number: 58
Registered: 3-2011
Posted on Monday, 16 April, 2012 - 07:04 am:   Edit PostDelete PostView Post/Check IP

Yes probably, you are right, on the bolt and the the spring push the motor to apply a pressure but I do not know which side? fan or rear?
and there is few washers ?
the motor work after refit but it is a little hard and I deduce a wrong refit .
Top of pagePrevious messageNext messageBottom of page Link to this message

Francois Charlier
Frequent User
Username: vonplum

Post Number: 59
Registered: 3-2011
Posted on Friday, 27 April, 2012 - 04:00 pm:   Edit PostDelete PostView Post/Check IP

the blower motor works good without noise.
The spring are on the rear of motor .
thank you

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Please quote Chassis Numbers for all vehicles mentioned.
Password:
E-mail:
Options: Enable HTML code in message
Automatically activate URLs in message
Action: